Catalog No. 22543 (1/03) Rev. 3.9 OWNERS MANUAL HF Oil Content Monitor (OCM) HF scientific inc. 3170 Metro Park
OCM Rev. 3.9 (1/03) 4 3.3.1 Power Source The power source required is 90 – 250VAC, 47-90Hz. The power consumption is 6VA. Connections are mad
OCM Rev. 3.9 (1/03) 5 4.0 Becoming Familiar with the Instrument The user interface of the OCM has been designed with a 4 key Touch Pad and a
OCM Rev. 3.9 (1/03) 6 5.0 Routine Operation The OCM is designed to measure and display the concentration of oil (in PPM by weight) in the bil
OCM Rev. 3.9 (1/03) 7 6.0 Instrument Configuration (SETUP mode) The OCM provides you the ability to customize your instrument according to yo
OCM Rev. 3.9 (1/03) 8 The current selected number of seconds will be shown. You can select the desired number of seconds for the “delay on” t
OCM Rev. 3.9 (1/03) 9 The current selected number of seconds will be shown. You can select the desired delay on time for this alarm using th
OCM Rev. 3.9 (1/03) 10 The three access codes used in the instrument: code 333 will provide access to instrument calibration, code 444 will p
OCM Rev. 3.9 (1/03) 11 7.0 Calibration Procedures The OCM has been factory-calibrated at HF scientific, inc.. It is possible to use the instr
OCM Rev. 3.9 (1/03) 12 the lower row of the LCD display. 15. This is the final step for calibration at the 0 PPM level; if you wish to skip
OCM Rev. 3.9 (1/03) 13 5. Replace the cleanout plug. 6. Press the ↵↵↵↵ key to initiate the calibration on 15 PPM water. The word CAL will ap
OCM Rev. 3.9 (1/03) 14 below) Press the ↵↵↵↵ key to initiate the zero adjust calibration on your oil-free sample. The word CAL will appear on
OCM Rev. 3.9 (1/03) 15 8.0 Self-Diagnostics: System Troubleshooting 8.1 System Warning Message(s) Automatic warning messages are generat
OCM Rev. 3.9 (1/03) 16 9.0 Routine Maintenance 9.1 Cleaning the Optical Chamber (Sample Tube) Proper measurement of the oil content of sample
OCM Rev. 3.9 (1/03) 17 10. Push the electronics module back in and tighten the four sensor cover screws. Please note that the OCM will
OCM Rev. 3.9 (1/03) 18 11.0 Warranty HF scientific, inc., as manufacturer, warrants to the original purchaser of this instrument that it wil
OCM Rev. 3.9 (1/03) 19 12.0 Figures Figure 1: Mounting Dimensions for the instrument [inches (mm)]
OCM Rev. 3.9 (1/03) 20 Figure 2: Recommended Plumbing for the instrument.
OCM Rev. 3.9 (1/03) 21 Figure 3: Electrical connections for the instrument.
OCM Rev. 3.9 (1/03) 22 Figure 4: Graphics of the LCD Display. The upper row ofthe display is ide
OCM Rev. 3.9 (1/03) 23 Figure 6: Location and removal of the desiccant cartridge on the instrument.
OCM Rev 3.9 (1/03) i Declaration of Conformity Application of Council Directive Standard to which Conformity is Declared: Product Safety – Tes
OCM Rev. 3.9 (1/03) 24 Figure 7: Lamp Replacement.
OCM Rev. 3.9 (1/03) 25 Figure 8: Menu Flow Chart
OCM Rev. 3.9 (1/03) 26 13.0 Approvals
OCM Rev. 3.9 (1/03) 27
OCM Rev. 3.9 (1/03) 28
OCM Rev. 3.9 (1/03) 29
OCM Rev. 3.9 (1/03) 30
OCM Rev. 3.9 (1/03) 31
OCM Rev. 3.9 (1/03) ii Table of Contents Declaration of Conformity...
OCM Rev. 3.9 (1/03) iii 8.2 System Failure Error...
OCM Rev. 3.9 (1/03) 1 Specifications Measurement Range 0-30 PPM, Trending 30-50 PPM Accuracy Less than ±5 PPM Resolution 1 PPM Response Time
OCM Rev. 3.9 (1/03) 2 1.0 Using this Instruction Manual Congratulations on your purchase of a new HF scientific inc. oil content monitor (OCM
OCM Rev. 3.9 (1/03) 3 3.0 Installation 3.1 Mounting and Site Selection The OCM is designed for wall mounting. If wall mounting is
Kommentare zu diesen Handbüchern